Graco 313296J Uživatelský manuál Strana 29
- Strana / 108
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Operation
313296J 29
3. Press while in the Ram Operation screen.
4. When the confirmation screen appears with a
prompt, select to start the pump.
5. Open the pump air valve (BF) and keep the director
valve (BC) set to DOWN while pump is operating.
NOTE: Increase air pressure to the ram if the pump
does not prime properly with heavier fluids.
Decrease air pressure if fluid is forced out around
the top seal or platen.
Automatic Crossover
(Tandem Supply System Only)
The automatic crossover feature allows continuous flow
and prevents system shutdown. If the active ram
encounters a pump runaway or drum empty alarm, it will
attempt an automatic crossover to the inactive ram.
The system will generate a crossover error if the active
ram attempts an automatic crossover while the inactive
ram has a pump runaway, drum empty, or not primed
alarm. If this occurs, correct the error and clear the
alarm from the Alarm screen. See Alarm Screen, page
103, for details.
Manual Crossover
(Tandem Warm Melt Supply System Only)
Manual crossover can only be initiated if the following
conditions are met:
• inactive ram is not in the drum empty error condi-
tion.
• pump runaway and not primed alarms do not exist.
To initiate a manual crossover to the inactive ram:
1. From the Ram Operation screen, press the Cross-
over key . The display prompts the operator
to confirm.
2. Select to confirm manual crossover operation
or select to cancel.
NOTE: If the active ram has a pump runaway error
or drum empty error, the system will attempt an
automatic crossover.
F
IG
. 25: Ram Operation Screen - Tandem System
Keep clear of the inactive ram, as automatic cross-
over may occur unexpectedly. To repair or adjust the
ram, first follow all steps of the Pressure Relief Pro-
cedure on page 28.
F
IG
. 26: Crossover Function Screen
- Warm Melt Supply 1
- Contents 2
- Related Manuals 3
- 4 313296J 4
- Warnings 5
- 6 313296J 6
- Overview 7
- Component Identification 8
- Tandem Supply Systems 9
- Integrated Air Controls 10
- Air Line Accessories 11
- Communications Gateway 11
- Fluid Control Module 12
- User Interface 13
- Depressurizing the 14
- Tandem ram: 14
- Single ram: 14
- 313296J 15 15
- User Interface Display 16
- Installation 17
- Connect Power Source 18
- Install/Adjust Drum Low or 19
- Empty Sensor 19
- Light Tower Accessory 19
- Attach Drum Stops 20
- Check Resistance 21
- Heater Resistance Checks 22
- Hose Installation and Care 23
- Overview of Temperature 23
- Control Settings 23
- Purge System 24
- Set Values on Display Module 24
- Load Material 25
- System Heat Up 26
- 313296J 27 27
- Operation 28
- Automatic Crossover 29
- Manual Crossover 29
- Recirculate Function 30
- Depressurize Function 30
- Change Drums 31
- Maintenance 32
- Platen Maintenance 33
- Electrical Enclosure 34
- Pump Heaters 35
- Diagnose Alarms 36
- Clear Alarms 36
- 313296J 37 37
- 38 313296J 38
- 313296J 39 39
- 40 313296J 40
- 313296J 41 41
- 42 313296J 42
- 313296J 43 43
- Troubleshooting 44
- 313296J 45 45
- 46 313296J 46
- Air Motor 47
- Displacement Pump 48
- Install Displacement Pump 49
- Disconnect Pump from Platen 50
- Connect Pump to Platen 51
- Replace Pump Heaters 51
- Replace Platen Heaters and 52
- 313296J 53 53
- Replace Platen Wipers 54
- Replace Ram Piston Rod Seals 54
- Software 56
- Replace Circuit Breakers 57
- Replace Electrical Enclosure 57
- Display/User Interface 58
- Replace Fluid Control Module 59
- Replace Cable Track 60
- Electrical Schematics 61
- D200 Ram A Schematic 62
- D200 Ram B 63
- Schematic 63
- D200 Junction Box Schematic 65
- D200 Cable Track Schematic 66
- D60 Single Ram Schematic 67
- D60 Ram A Schematic 68
- D60 Ram B 69
- D60 Pump and Platen Schematic 70
- D60 Junction Box Schematic 71
- D60 Cable Harness Schematic 72
- 313296J 75 75
- 76 313296J 76
- 313296J 77 77
- Kit 24D016 Shown 78
- 313296J 79 79
- 80 313296J 80
- UBFB 81
- 82 313296J 82
- Kit 24D010 Shown 83
- 84 313296J 84
- 313296J 85 85
- 313296J 87 87
- Platen 24D066 (20L) Shown 88
- 313296J 89 89
- Electrical Enclosure Parts 90
- Accessories 92
- Display Overview 93
- Display Details 93
- Soft Keys 94
- Navigation within Screens 94
- Setup Mode Screens 95
- Maintenance Setup Screen 96
- Hardware Setup Screens 97
- Advanced Setup Screens 98
- Advanced Setup Screen 3 99
- Run Mode Screens 100
- Heat Run Screen 101
- Status Screen 102
- Maintenance Screen 102
- Icon Function 102
- 313296J 103 103
- Dimensions 104
- D60 Models 105
- Technical Data 106
- 313296J 107 107
- Graco Standard Warranty 108
- Graco Information 108
Související produkty a manuály pro ne Graco 313296J
ne Graco Crib PD171330A Uživatelský manuál
(88 stránky)
(88 stránky)
(88 stránky)
ne Graco 3A0418E Uživatelský manuál
(20 stránky)
(20 stránky)
ne Graco 307883G Uživatelský manuál
(14 stránky)
(14 stránky)
ne Graco 300627EN-D Uživatelský manuál
(12 stránky)
(12 stránky)
ne Graco PD116361B Uživatelský manuál
(40 stránky)
(40 stránky)
ne Graco 3A2805K Uživatelský manuál
(52 stránky)
(52 stránky)
ne Graco 3A1334E Uživatelský manuál
(32 stránky)
(32 stránky)
ne Graco 3A1333A Uživatelský manuál
(6 stránky)
(6 stránky)
ne Graco Husky 1050HP Uživatelský manuál
(2 stránky)
(2 stránky)
ne Graco 311014D Uživatelský manuál
(2 stránky)
(2 stránky)
ne Graco 3A1495C Uživatelský manuál
(16 stránky)
(16 stránky)
ne Graco 221521 Návod k použití a péči
(1 stránky)
(1 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.102 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce