Graco 313296J Uživatelský manuál Strana 101
- Strana / 108
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Appendix A - User Interface Display
313296J 101
Heat Run Screen
The Heat Run screen displays information for four to six
heat zones. See F
IG
. 72 for information about each
zone. For each zone, the icon on the upper right is pres-
ent if the zone is enabled, otherwise the space is blank.
The temperature unit is shown in the upper right of the
menu bar. An alarm icon displays in the bottom right if
there is an alarm or deviation on a heat zone. Press the
soft key under the alarm icon to clear the alarm or devia-
tion.
NOTE: Heat zones five and six are located in the
two-zone expansion kit.
Heat zones seven through ten are located on Ram B.
Heat zones eleven and twelve are located in the
two-zone expansion kit.
The last digit in the temperature control module alarm
codes represents the zone reporting the alarm.
From the Heat Run screen, users can view heat zone
information for each ram, put heat zones into Setback
mode, turn heaters on and off for enabled heat zones,
and change the individual zone temperature settings.
View Heat Zone Information
To view heat zone information, press to
scroll through the Heat Run screens.
NOTE: Must exit edit mode to scroll through the
Heat Run screens.
Setback Mode
To put heaters into setback mode for enabled heat
zones, press . The setpoint for each zone will be
decreased by the setback amount set on Heater Sys-
tem Setup Screen, page 95.
Turn On Heaters
See System Heat Up, page 26, for instructions.
Change Zone Temperature Setting
Press to access the fields to make changes. Use
the navigation buttons to move to the desired heat zone.
Enter the new temperature and press to save the
change. Press to exit edit mode.
Zone
Number
Temperature Control
Module Alarm Code
A1 1
A2 2
A3 3
A4 4
A5 5
A6 6
B1 7
B2 8
B3 9
B4 10
B5 11
B6 12
F
IG
. 72: Heat Run Screen - Ram A
System component
being heated
Zone set point
Zone
number
Current zone temperature
- Warm Melt Supply 1
- Contents 2
- Related Manuals 3
- 4 313296J 4
- Warnings 5
- 6 313296J 6
- Overview 7
- Component Identification 8
- Tandem Supply Systems 9
- Integrated Air Controls 10
- Air Line Accessories 11
- Communications Gateway 11
- Fluid Control Module 12
- User Interface 13
- Depressurizing the 14
- Tandem ram: 14
- Single ram: 14
- 313296J 15 15
- User Interface Display 16
- Installation 17
- Connect Power Source 18
- Install/Adjust Drum Low or 19
- Empty Sensor 19
- Light Tower Accessory 19
- Attach Drum Stops 20
- Check Resistance 21
- Heater Resistance Checks 22
- Hose Installation and Care 23
- Overview of Temperature 23
- Control Settings 23
- Purge System 24
- Set Values on Display Module 24
- Load Material 25
- System Heat Up 26
- 313296J 27 27
- Operation 28
- Automatic Crossover 29
- Manual Crossover 29
- Recirculate Function 30
- Depressurize Function 30
- Change Drums 31
- Maintenance 32
- Platen Maintenance 33
- Electrical Enclosure 34
- Pump Heaters 35
- Diagnose Alarms 36
- Clear Alarms 36
- 313296J 37 37
- 38 313296J 38
- 313296J 39 39
- 40 313296J 40
- 313296J 41 41
- 42 313296J 42
- 313296J 43 43
- Troubleshooting 44
- 313296J 45 45
- 46 313296J 46
- Air Motor 47
- Displacement Pump 48
- Install Displacement Pump 49
- Disconnect Pump from Platen 50
- Connect Pump to Platen 51
- Replace Pump Heaters 51
- Replace Platen Heaters and 52
- 313296J 53 53
- Replace Platen Wipers 54
- Replace Ram Piston Rod Seals 54
- Software 56
- Replace Circuit Breakers 57
- Replace Electrical Enclosure 57
- Display/User Interface 58
- Replace Fluid Control Module 59
- Replace Cable Track 60
- Electrical Schematics 61
- D200 Ram A Schematic 62
- D200 Ram B 63
- Schematic 63
- D200 Junction Box Schematic 65
- D200 Cable Track Schematic 66
- D60 Single Ram Schematic 67
- D60 Ram A Schematic 68
- D60 Ram B 69
- D60 Pump and Platen Schematic 70
- D60 Junction Box Schematic 71
- D60 Cable Harness Schematic 72
- 313296J 75 75
- 76 313296J 76
- 313296J 77 77
- Kit 24D016 Shown 78
- 313296J 79 79
- 80 313296J 80
- UBFB 81
- 82 313296J 82
- Kit 24D010 Shown 83
- 84 313296J 84
- 313296J 85 85
- 313296J 87 87
- Platen 24D066 (20L) Shown 88
- 313296J 89 89
- Electrical Enclosure Parts 90
- Accessories 92
- Display Overview 93
- Display Details 93
- Soft Keys 94
- Navigation within Screens 94
- Setup Mode Screens 95
- Maintenance Setup Screen 96
- Hardware Setup Screens 97
- Advanced Setup Screens 98
- Advanced Setup Screen 3 99
- Run Mode Screens 100
- Heat Run Screen 101
- Status Screen 102
- Maintenance Screen 102
- Icon Function 102
- 313296J 103 103
- Dimensions 104
- D60 Models 105
- Technical Data 106
- 313296J 107 107
- Graco Standard Warranty 108
- Graco Information 108
Související produkty a manuály pro ne Graco 313296J
ne Graco Crib PD171330A Uživatelský manuál
(88 stránky)
(88 stránky)
(88 stránky)
ne Graco 3A0418E Uživatelský manuál
(20 stránky)
(20 stránky)
ne Graco 307883G Uživatelský manuál
(14 stránky)
(14 stránky)
ne Graco 300627EN-D Uživatelský manuál
(12 stránky)
(12 stránky)
ne Graco PD116361B Uživatelský manuál
(40 stránky)
(40 stránky)
ne Graco 3A2805K Uživatelský manuál
(52 stránky)
(52 stránky)
ne Graco 3A1334E Uživatelský manuál
(32 stránky)
(32 stránky)
ne Graco 3A1333A Uživatelský manuál
(6 stránky)
(6 stránky)
ne Graco Husky 1050HP Uživatelský manuál
(2 stránky)
(2 stránky)
ne Graco 311014D Uživatelský manuál
(2 stránky)
(2 stránky)
ne Graco 3A1495C Uživatelský manuál
(16 stránky)
(16 stránky)
ne Graco 221521 Návod k použití a péči
(1 stránky)
(1 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.099 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce